Call: (407) 944-8856

GEM4060 Adjustable Gable End Antenna Mount Pipe Bracket

3S GEM-4060 Adjustable Eave Mount Antenna Mast Bracket

Used for easy mounting on the eave of a house. Both the upper and lower brackets are for masts up to 1.50 inches in diameter with clamps, bolts and 2.5 inch lag screws. Pipe can pass by lower Bracket for Ground mount installations (Mast Not Included).

VMP Adjustable Gable End Antenna Mount Mast Bracket

8' Foot X 1.25" OD 18 AWG Galvanized Antenna Mast Pole | EZ 8-18 - $27.00

EZ 8-18 8 Foot Galvanized

Made in the USA!
This is a 9 Foot (108") by 1.25" OD 18 AWG Galvanized Antenna Mast (Mount Not Included)...

8' Foot X 1.25" OD 18 AWG Galvanized Antenna Mast Pole - Swaged | EZ 8-18S - $27.65

EZ 8-18S 8 Foot Galvanized

Made in the USA!
This is a 8 Foot (96") by 1.25" OD 18 AWG Swaged Galvanized Antenna Mast (Mount Not Included)...

5' Foot by 1.25" OD 18 AWG Galvanized Antenna Mast Pole | EZ 5-18 - $14.50

EZ 5-18 5 Foot Galvanized
Made in the USA!
This is a 5 Foot (60") by 1.25" OD 18 AWG Galvanized Antenna Mast (Mount Not Included)...

5' Foot by 1.25" OD 18 AWG Galvanized Antenna Mast Pole - Swaged | EZ 5-18S - $14.95

EZ 5-18S 5 Foot 18 AWG Swaged Antenna Mast Section
Made in the USA!
This 5 Foot (60") by 1.25" OD 18 AWG swaged end Antenna Mast tube is galvanized for weather and used to extend any 1-1/4 inch 18 gauge antenna masts by fitting the swaged end of this mast into the open end of the other mast tube, thereby extending the existing mast an additional 5 feet. Manufacturers recommend that masts heights of 10 feet and higher be guyed...

5' Foot X 1.25" OD 16 AWG Galvanized Antenna Mast Pole - Swaged | EZ 5-16S - $16.30

EZ 5-16S 5 Foot 16 AWG Swaged Antenna Mast Section
Made in the USA!
This 5 Foot (60") by 1.25" OD 16 AWG swaged end Antenna Mast tube is galvanized for weather and used to extend any 1-1/4 inch 16 gauge antenna masts by fitting the swaged end of this mast into the open end of the other mast tube, thereby extending the existing mast an additional 5 feet. Manufacturers recommend that masts heights of 10 feet and higher be guyed...

5' Foot X 1.25" OD 16 AWG Galvanized Antenna Mast Pole | EZ 5-16 - $16.00

EZ 5-16 5 Foot Galvanized
Made in the USA!
This is a 5 Foot (60") by 1.25" OD 16 AWG Galvanized Antenna Mast (Mount Not Included)...

8' Foot X 1.25" OD 16 AWG Galvanized Antenna Mast Pole | EZ 8-16 - $27.00

EZ 8-16 -8 Foot Galvanized

Made in the USA!
This is a 9 Foot (108") by 1.25" OD 16 AWG Galvanized Antenna Mast (Mount Not Included)...

8' Foot X 1.25" OD 16 AWG Galvanized Antenna Mast Pole - Swaged | EZ 8-16S - $27.95

EZ 8-16S -8 Foot 16 AWG Swaged Antenna Mast Pre- Galvanized
Made in the USA!
This is a 9 Foot (96") by 1.25" OD 16 AWG Galvanized Antenna Mast (Mount Not Included)...

Rate this product.

Product isn't rated yet. Write a review.

Eave & J Mounts For Antenna Mast Pipe

The first key to any reception is to get above obstructions that exist between you and your target, as radio frequency reception of any kind (satellite, microwave, Radio and TV) are for the most part "Line-of-Sight" dependant. The fact that some receptions occur without line of sight is due to phenomenon not applicable in this discussion. As you increase your target distance, you increase the territory you must account for in maintaining line-of-sight. What tall building and air traffic exist in this corridor, no one can account for. Aircraft are very good at messing up reception for a number of reasons, even when flying way above the path, again removed for clarity in this discussion. Height, is therefore key in optimizing your ability to capture the best line-of-sight possible to your target.

The Roof of any Building of Home provides a Logical Platform of Height in which Line-of-Sight is more likely to occur, or from which, more height can easily be obtained. These Mounts are Quality made by Manufacturers with a History in the Field of Proven Success and Longevity. Whether you are planning to Install your Antenna and Mount to the Roof Peak, Gable, Vent Pipe, Chimney or Pitch, Please plan your installation to Minimize the Structural and Asthetic Impact to your House or Building, research and follow all applicable Local Building Codes and annex the appropriate Structural Engineering Assistance when utilizing Non-Penetrating Mounts with Concrete Cinder Block Ballast on any Flat or Pitched Roof.