Call: (407) 944-8856

Rohn RSL Tube Braced Tower Section R8H

Rohn R8H RSL Tower Section With Legs & Tube Braces

This is a set of (12) 52 inch x 1-1/4 inch 16 AWG Hot Dipped Galvanized steel tube braces and (3) 10' 4" U Legs that form the R1 Section of RSL Tower

Includes:

12 x 52 inch Tube Braces 1-1/4 inch x 16 ga
3 x 10 Foot 4 inch U Legs 2-3/4" x 1/4"

Bolt Assy. Kit for Braces

RSL SBK Section Bolt Kit ( Optional )

All three tower legs in each section have provision to install step bolts and a safety climb system. When step bolts are desired, one step bolt kit must be ordered for each section of the tower. Increase the number of step bolt kits accordingly when step bolts are desired on more than one tower leg of a section

U-shaped legs allows for simple lap splice connection .Available in standard and heavy models. Pre-punched holes for attachment of safety climb systems, mounting kits, etc. Braces for each section are the same length, while bolt lengths are standard throughout the tower . Tower material is hot-dip galvanized

Warranty Sheet

Note:

*Per Rev G requirements, any structure greater than 10’ requires a climber safety device.

Rohn RSL Section Bolt Kit RSLSECBK - $38.00

RSLSECBK Section Bolt Kit
Rohn RSL Tower Bolt kit for 10’ tower section. Order one kit for each section of rsl tower .....

Rohn RSL Tower Step Bolt Kit RSLSTEP - $59.00

RSLSTEP Step Bolt Kit
Rohn RSL Tower Step Bolt kit consists of (10) 5/8” x 7” steps for one 10’ tower section. Order one kit for each section of tower for step bolts on one leg.

TTRSL50 Safety Cable System for Rohn RSL Tower 20 to 50 foot - $580.00

TTRSL50 Safety Cable System
Rohn RSL (20' - 50') Tower installed Component of the TUF TUG Safety System. With enough fixtures and climbing cable to install on Towers up to 50 foot in height. Does not include Harness or Wire Grab.

TTRSL100 Safety Cable System for Rohn RSL Tower 60 to 100 foot - $850.00

TTRSL100 Safety Cable System
Rohn RSL (60' - 100') Tower installed Component of the TUF TUG Safety System. With enough fixtures and climbing cable to install on Towers up to 100 foot in height. Does not include Harness or Wire Grab.

Rohn RSL Tower Top Plate Kit RTP12 - $372.00

RTP12 Top Plate RSLSection R1 & R2

The RTP12 Top Plate Kit Mounts to top closing angles provided with tower kit to RSL tower section R1 or R2. Hole pattern fits TB3 ,TB4 thrust bearings and RSLTMA Top Mast Kit ( Optional ). Kit includes plate and attachment hardware.

Rohn RSL Tower Top Mast Kit RSLTMA - $156.00

RSLTMA Top Mast Kit
2.38” O.D. x 0.154” wall x 3’ mast mounts to top plate kit. Top plate kit must be ordered separately.

Rohn RSL Tower Anti-Climb Brackets RACW - $345.00

RACW Anti-Climb Brackets
Rohn RSL Tower Anti-Climb Brackets to be used with barbed or razor wire (wire not included). Kit includes (3) outer and (3) inner brackets with required mounting hardware.

RASK5 Accessory Shelf for RSL Tower Section 5 - $450.00

RASK5 Accessory Shelf
Rohn Accessory Shelf for RSL Tower section 5. Shelf mounts on tower legs approximately 4' 6" below the top. Kit includes plate and attachment hardware. Top plate, if required, must be ordered separately.

RASK34 Accessory Shelf for RSL Tower Sections 3 And 4 - $425.00

RASK34 Accessory Shelf
Rohn Accessory Shelf for RSL Tower sections 3 and 4. Shelf mounts on tower legs approximately 4' 6" below the top. Kit includes plate and attachment hardware. Top plate, if required, must be ordered separately..

RASK12 Accessory Shelf for RSL Tower Sections 1 And 2 - $296.00

RASK12 Accessory Shelf
Rohn Accessory Shelf for RSL Tower sections 1 and 2. Shelf mounts on tower legs approximately 4' 6" below the top. Kit includes plate and attachment hardware. Top plate, if required, must be ordered separately.

Rate this product.

Product isn't rated yet. Write a review.