ROHN TBSAFETYTower Down Guy Turnbuckle Safety Wire and Clamps Kit
Kit Includes:
14001 (1 ea) U-Bolt Clip 1/4 Galv Forged
R-1/44GW15 (1 ea) 15 Feet Guy Wire 1/4 High Strength
Use consists of (15') 1/4 inch guy wire with 6,650 lbs breaking strength and (2) 1/4 inch clamps. Use 15' of guy wire + 2 clamps on each anchor assembly for protection against snapping. This Strand weaves in, out and Through each Eye to Eye or Eye to Jaw Turnbuckle (ie R-3/8TBE&J or R-3/8TBE&E) up to 1" and the attached Down Guy Anchor to prevent Turnbuckles from Vibrating Loose or otherwise coming undone. Incudes ROHN Part Numbers; 140001 (Galvanized Forged 1/4 inch U-Bolt Clip) and R-1/4GW15 (15 Foot of 1/4 High Strength Guy Wire). Turnbuckles and Equalizer Plates are not included
This Down Guy Turnbuckle Safety Kit is included in your Complete ROHN Guyed Tower Kits. Install the Down Guy Anchor Types as indicated by the ROHN Catalog (Footer Links below) as per REV. G or REV. F Wind Load Ratings. Space and Install in the Concrete Anchor Rods in Anchor Blocks as Specified for the Particular Height and Wind Load Application by Model Number. Then Install these kits to secure the Turnbuckles as Finished.
The recommended initial tension in guy wires is 10% of their ultimate tensile strength. There are two different grades of steel used for good guy line (clothes line does not count), HS (high strength) and EHS (extra high strength). The Rohn manual gives the following info on 3/16 and 1/4 in cable.
ROHN 25SS020 Complete 20 Foot Self Supporting Tower
with with (1) 10' Tower Section, (1) Top Cap Section, (1) 5' Base Section and Grounding (optional), less Foundation and Installation...
ROHN 1/4CCF 1/4" Down Guy Wire Cable Clamp Galvanized Drop Forged Steel
Use 3 of these when Terminating 1/4 inch wire strand used in ROHN Towers Down Guys for both Temporary and Permanent Scenarios...
ROHN 3/8TBE&E 3/8" x 6" Eye to Eye Turnbuckle Federal Spec FF-T-791B Type 1 Form 1; Forged, Hot Dip Glavanized, Open Body, Working Load Limit: 1200 lbs., Ultimate Strength: 6000 lbs. Typical Use: when attaching and tensioning ROHN Tower and Telescopic Antenna Mast Down Guy terminations (3/16" Strand via Pre-formed deadend and 5/16THH, 1/4" Bare Strand via Cable Clamps and 5/16THH, or 618/620 Bare Wire via Cable Clamps/Gripple and 1/4TH) to Equalizer Plate Anchors (Sandwich Plated like GAC305/EP25345 or GAC303/EP25343)... Read More.
ROHN 3/8TBE&J 3/8" x 6" Eye to Jaw Turnbuckle Federal Spec FF-T-791B Type 1 Form 1; Forged, Hot Dip Glavanized, Open Body, Working Load Limit: 1200 lbs., Ultimate Strength: 6000 lbs. Typical Use: when attaching and tensioning ROHN Tower and Telescopic Antenna Mast Down Guy terminations 3/16" Strand via Pre-formed deadend and 5/16THH, 1/4" Bare Strand via Cable Clamps and 5/16THH, or 618/620 Bare Wire via Cable Clamps/Gripple and 1/4TH) to Closed Eye or Integral Equalizer Plate Anchors (like GAS4303/EZ 30 or GAC3455). Will NOT fit a GAR30 Anchor...
Read More.
ROHN 5/8TBE&E 5/8" x 12" Eye to Eye Turnbuckle Federal Spec FF-T-791B Type 1 Form 1; Forged, Hot Dip Glavanized, Open Body, Working Load Limit: 3500 lbs., Ultimate Strength: 17500 lbs. Typical Use: when attaching and tensioning ROHN Tower Down Guy terminations (1/4" Bare Strand via Cable Clamps and 5/16THH, 1/4" Strand via Pre-formed deadend and 3/8THH, 5/16" Strand via Pre-formed deadend and 7/16THH or 5/16" Bare Strand, 3/8" Strand via Pre-formed deadend and 1/2THH or 3/8" Bare Strand via Cable Clamps and 7/16THH) to Equalizer Plate Anchors (Sandwich Plated like GAC305/EP25345 or GAC303/EP25343)... Read More.
ROHN 5/8TBE&J 5/8" x 12" Eye to Jaw Turnbuckle Federal Spec FF-T-791B Type 1 Form 1; Forged, Hot Dip Glavanized, Open Body, Working Load Limit: 3500 lbs., Ultimate Strength: 17500 lbs. Typical Use: when attaching and tensioning ROHN Tower Down Guy terminations (1/4" Bare Strand via Cable Clamps and 5/16THH, 1/4" Strand via Pre-formed deadend and 3/8THH, 5/16" Strand via Pre-formed deadend and 7/16THH or 5/16" Bare Strand via Cable Clamps and 3/8THH, 3/8" Strand via Pre-formed deadend and 1/2THH or 3/8" Bare Strand via Cable Clamps and 7/16THH) to Closed Eye GAR30 or Integral Equalizer Plate Anchors (like GAC3455TOP, GAC5655TOP or GAC5755TOP)... Read More.
ROHN 1/2TBE&E 1/2" x 12" Eye to Eye Turnbuckle Federal Spec FF-T-791B Type 1 Form 1; Forged, Hot Dip Glavanized, Open Body, Working Load Limit: 2200 lbs., Ultimate Strength: 11000 lbs. Typical Use: when attaching and tensioning ROHN Tower Down Guy terminations 3/16" Strand via Pre-formed deadend and 5/16THH, 1/4" Bare Strand via Cable Clamps and 5/16THH, 1/4" Strand via Pre-formed deadend and 3/8THH to Equalizer Plate Anchors (Sandwich Plated like GAC305/EP25345 or GAC303/EP25343)... Read More.
ROHN R-340020 5/8" x 8' Bonded Ground Rod Uniform Electrolytic Copper On Steel Core, Minimum Copper Depth 10 Mils, UL Listed. Use 5/8 inch Ground Rod Clamp for #6, #4 copper, use 3/4 inch clamp with steel wire rope (sold separately). Suitable for burial after attachment (see our self amalgamating tape sealant). Use for REV. F Grounding of Tower Base and Down Guys or Telescopic Antenna Masts. Select a ground rod clamp based on conductor to be attached (see details)... Read More.
ROHN 1/2TBE&J 1/2" x 12" Eye to Jaw Turnbuckle Federal Spec FF-T-791B Type 1 Form 1; Forged, Hot Dip Glavanized, Open Body, Working Load Limit: 2200 lbs., Ultimate Strength: 11000 lbs. Typical Use: when attaching and tensioning ROHN Tower Down Guy terminations 3/16" Strand via Pre-formed deadend and 5/16THH, 1/4" Bare Strand via Cable Clamps and 5/16THH, 1/4" Strand via Pre-formed deadend and 3/8THH to Closed Eye GAR30 or Integral Equalizer Plate Anchors (like GAC3455TOP or GAC5655TOP)...
ROHN BGK2G Tower Base Section Grounding Kit
Primarily for 25G,45G,55G and 65G REV. F Towers, also used in Self-Supporting Tower Kits. Comprises enough material to ground 1 Tower Base Section Tubular Rail. Consists of (1) 5/8"x8' Ground Rod, (1) Rod Clamp (1) J-Clamp 1-1/4 to 2 inch and 10 feet of #4 Solid Copper Wire...