EZ-FRM-166 Non-Penetrating Roof Mount -w- 57" x 1.66" OD Mast
Made in the USA!
Ideal for Light Off-Air TV and Wireless Internet Antenna mounting, is constructed of pre-galvanized 12 ga. steel, uses 6 standard concrete blocks to anchor, 35" x 35" base. Mast pipe length will be 57" actual length for shipping purposes.
For light antenna loads needing 10 feet in total height,
the Optional 1.66" x 57" Swaged Pipe extension kit includes:
(1) EZ 5-166S Swaged Pipe
(1) EZ 60A-50' Steel Guy Wire
(1) EZ 43-A Guy Ring
(8) 1/8" CCF Guy Clamps
Height and Antenna Loading capability are dependent upon ballast weight... You need to Consult an Engineer to determine the Load Bearing Capability of the roof that you are entertaining such an Installation. It is Important to choose a Mount and Mounting Location with a Picture of the Finished Installation in Mind. Be Sure to First select a location that lends itself to applying a Load without Compromising the Integrity of the Material you affix to. Most Decorative Finishes most often do not have the Strength to Hold a Weight or Pressure without fail. Further, Think about what's underneath the exterior. Is it stronger, or will it yield to Pressure over time also? Weather Proof the Installation to Maintain the Integrity of your Home. Next consider the Location over a Lifetime of Adjustments, does it lend itself to modifications in Height or Direction? Larger Antennas increase the surface area presented to air movement, Hence, Wind-load does increase. As the length of the mast increases from Its last attached point on the structure, the torque applied in cantilever also increases with Weight and Wind-Load, requiring a more substantive attachment and Load-Bearing material. Keep the Distance Minimal from the Antenna to the TV's and Equipment you feed, as to minimize loss and the need for Amplification.
EZ 5-18S 5 Foot 18 AWG Swaged Antenna Mast Section Made in the USA!
This 5 Foot (60") by 1.25" OD 18 AWG swaged end Antenna Mast tube is galvanized for weather and used to extend any 1-1/4 inch 18 gauge antenna masts by fitting the swaged end of this mast into the open end of the other mast tube, thereby extending the existing mast an additional 5 feet. Manufacturers recommend that masts heights of 10 feet and higher be guyed...
EZ 43-A Adjustable 3-Way Down Guy Ring Made in the USA!
Adjustable mount Down Guy Ring, for 3-Way guying of Antenna masts with Screw Eye Bolts to affix 620 guy wire, Fits Masts up to 1 1/4" (Mast and Wire Not Included)...
EZ 60A 620 Steel Antenna Mast Down Guy Wire Made in the USA!
50 foot segment of 6 Strand, 20 Gauge Steel Antenna Mast Down Guy Wire for Light Duty Antenna Mast Guying. Comes as 50 foot Hank section. Multiple quantities ordered will come in contiguous footage up to 1000 feet...
ROHN 1/8CCF 1/8" Down Guy Wire Cable Clamp Galvanized Drop Forged Steel
Use 2 of these when Terminating 620 (CM 9080) and 618 (ROHN 618) wire strand used in Telescopic and Regular TV Antenna Mast Down Guys for both Temporary and Permanent Scenarios...
EZ 50 1/4" Eye Bolt Turnbuckle for 620 Wire Down Guy Tensioning Made in the USA!
Turnbuckle with 1/4" Screw Eye Bolts to affix 620 guy wire for tensioning down guys on Masts up to 1 1/4" (Mast and Wire Not Included)...
Gripple 1/8" 20ga Down Guy Wire Cable Rope Grip
Use with Gripple Tool (TGTP) when Terminating 6-20 (CM 9080) guy wire strand. Used in Telescopic and Regular TV Antenna Mast Down Guys to easily Secure and Tension Multiple Guy Wires at the Anchor end...