Printer Friendly Tell a Friend

ROHN 25G Bracketed Tower Wall Mount Kit 25GWM

Highlights
Hot Dip Galvanized
Bolted Joints
Rail Clamps included
Can be used in:
Bracketed Config.s
Price: $504.89
Manufacturer Code: 25GWM
Stock Level: 1
Qty:
Availability: Usually ships in 24 Hrs
Shipping: Can ship anywhere
ROHN 25GWM 25G Tower Wall Mount Bracket Kit
Made in the USA!Made in the USA!
The ROHN 25GWM allows you to wall mount the base of a Bracketed 25G Tower Kit. This wall mount gives you the ability to install more load than is typically available on a standard wall mount. The wall mount also helps to keep the ground area around the tower location usable. The 25GWM assembly comes complete with both top and bottom wall mounting bracket materials and stub leg base plate for connection to a standard ROHN 25G tower section.
1. It is the purchaser's responsibility to verify that their installation and building structure are able to withstand all loads imposed by the antenna system and mount.
2. All antenna installations should be grounded, by installer, to meet all applicable codes.
3. All parts are hot-dip galvanized after fabrication.
4. All sealant to be supplied by others, if required.
5. Local zoning, building codes and insurance companies may require an architect or structural engineer's approval
prior to installation.
6. Inspect the mount and antenna installation every 6 months and after severe weather.
7. Holes provided in mounting angles are 11/16" diameter for use with HDG 5/8 inch threaded rod, provided by others.


Note: Bracketed Towers are Specifically useful when your project calls for a Tower to rise above the building's height, but for various asthetic and Weight Bearing Load considerations, cannot construct the tower upon the roof itself. The Bracket Tower Scenario relies on the Building's Load Bearing Outside Wall, using a portion of it to bolt on the base and first bracket, establishing a secure cantilever, whereupon the tower can rise as a Self-Supporting Structure above the building's roof without unsightly guy wires or a ground presence below. Self-Supporting Towers are limited in Height due to the nature of Antenna and Ice loads versus the Cantilever Nature Of Wind against them, offset by the weight of the Foundation and the cohesive of the soil to counter Tower tipover, as well as the strength of the tower members to withstand these Forces against them. ROHN Tower Kits are designed based on assumptions made regarding Windspeed, EPA (Antenna Load), Height, Standard Soil Conditions, Surrounding Environment and Duty. The Pre-packaged Kits contain the parts called for based on this Stock Design. The Stock Design of these Kits does not account for the Variations of Historic Windspeed, Number of Antenna(e) Loading at Specific Height(s), Soil Engineering recommendations, Adjacent Structures, Communications Purpose, or Geo-Political Rules, Laws and Codes That will be Applicable to Your Project. It is Recommended that you take the time to engage an local Engineer that has the expertise and available Information necessary to evaluate the Stock design for Applicability, and/or find the Tower Quote Data Sheet Form by clicking the link that appears on the Footer of this Page Below. *Per Rev G requirements, any structure greater than 10 ft requires a climber safety device. ROHN Produces this series of Brackets specifically for the 25G Tower in exterior wall mount applications. Sturdy and Adjustable, this galvanized American Steel bracket is no comparison to the ROHN Clone brackets you may find at other Sites. Buy ROHN, Buy American.
Specification Sheet
Spec Sheet
Product isn't rated yet. Write a review.

It is Important to choose an Antenna Mount and Wall Mounting Location with a Picture of the Finished Antenna Installation in Mind. Be Sure to First select a location that lends itself to applying a Vertical, Cantilevered, Twisting Load without Compromising the Integrity of the Wall Material you affix to. Most Modern Exterior Decorative Wall Finishes most often do not have the Strength to Hold the Weight and Pressure of a Large TV Antenna under Wind Load without fail. Beams and Studs within the Wall are an Absolute Must to Locate when the Wall Composition is anything other than Solid wood or Concrete. Attach to these Strength Members. Further, Think about what's underneath the Wall exterior. Is it stronger, will it yield to Pressure over time as well? Sandwich additional Material (wood or steel) to the backside or both sides of the wall at the points where the mount attaches, as to distribute the load on relatively weak wall materials and to dampen vibration from Wind. Weather Proof the Installation to Maintain the Integrity of your Home. Next consider the Location over a Lifetime of Adjustments, does it lend itself to modifications in Height or Direction? Larger Antennas increase the surface area presented to air movement, Hence, Wind-load does increase. As the length of the mast increases from Its last attached point on the structure, the torque applied also increases with Weight and Wind-Load, requiring a more substantive attachment and Load-Bearing material. Keep the Distance Minimal from the Antenna to the TV's and Equipment you feed, as to minimize loss and the need for Amplification. Further, the NEC (National Electrical Code partly defines a good Ground connection as being as short as possible, you must affix a connection to a good Earth Ground prior to Premise entry or Bond to an existing one.

Products   Recently Viewed
Your Cart
Credit Cards Taken
Your shopping cart is empty!
We Ship Fast!
Your Orders leave Daily! UPS... What can Brown do for You?!United States Postal ServiceR+L Carriers... Value Added Advantages!