Your Cart
Credit Cards Taken
Your shopping cart is empty!
We Ship Fast!
Your Orders leave Daily! UPS... What can Brown do for You?!United States Postal ServiceR+L Carriers... Value Added Advantages!
Printer Friendly Tell a Friend

4-Way Cable TV Antenna Signal Splitter 1GHz GRS4DGV

Highlights

    Specifications

Bandwidth  5-1000MHz

Insertion   -4.5dB max.

Isolation      -20dB min

Return Loss -15dB min

Epoxy of Rear cover

110dB RFI shield.
Price: $4.60
Manufacturer Code: GRS4DGV
Stock Level: 0
Availability: Call to Order
Shipping: Can ship anywhere
Regal GRS4DGV 2-Way Splitter for Cable TV Antenna Signal Distribution 1 GHz
Gold/Red Splitter achieve 1 GHz frequency by employing printed circuit board technology. This PCB is enclosed in a chromate-treated zinc alloy housing with a tongue and groove backplate/housing interface to produce a 110 dB EMI shielding. Machined F ports, flat mounting tabs and an integral heavy duty ground block further enhance this latest addition to the Regal line.


Note: This is one of those Splitter you would find or use inside of those steel lock-boxes on the side of an Apartment complex, or the little Grey box on the side of your Home or Office that the Cable TV company installed. It features Vertical Port F Connections. Its typically used inside of these little boxes because it's easier to connect/disconnect the cables when all the F connection Ports are facing in the same direction. So when you are mounting a 4-Way Splitter In a tight space without a lot of room around it for the RG6 Coaxial Cable to make connection, this is the one you want! It will pass Forward and Return signals; making it perfect for Splitting Cable TV with High-Speed Internet Connection Signals. The Voltage Protection also makes it suitable for splitting HD TV Antenna Signals as well. The Flat F Connector ends means that the connection to the RG coaxial cable you use (RG6 or RG11) is solid, secure and doesn't slip or back off after tightened with appropriate force (most Coaxial Cable Manufacturers specify in inch/pounds).
Product isn't rated yet. Write a review.

4-Way Splitters are typically the Part you would use to take One (1) cable Feed and "Split" it into Four (4) in order to Provide Signal to 4 Independant Devices, or Three More Cables to complete the Run(s) to their Final Destination(s). Please be Sure to Select the Appropriate Splitter not just By Manufacturer and Price. But Rather, Consider the Specifics of Bandwidth, Packaging (Indoor vs. Outdoor), Loss, Powering Requirements Up/Down-Stream and the Overall Needs of the Final System You Wish to Create...

If you are adding a splitter to an existing Cable TV or Antenna feed, you may need to compensate for the loss that you are about to introduce. The gain of a Line Amplifier should be selected to zero out the loss that follows it. In other words, if you have fifty feet of cable and a two-way splitter, then a 10 db amplifier will be fine. Conversely, if you have an eight-way splitter and hundreds of feet of cable, you will need an amplifier with a higher gain. Just as in the case of a Pre-Amplifier, however, bigger is not always better.

Commensurate with Coaxial Cable TV Antenna Splitter Installation, you want to Ground your Cable TV or HDTV Antenna Coaxial Cable System Outside before bringing the TV Cable Inside. This way, Lightning Strikes and Power Surges have an opportunity to arrest before reaching your TV and Entertainment Electronics. The Integral Grounding Block designed onto every Outdoor Use Compatible RF Signal Splitter we sell will effectively convey this unwanted Electrical Energy to a Ground Rod via a Copper Ground Wire that you Install (not included). Consult your Local Building Code and NEC for guidance to Properly Grounding your HD TV Antenna, Cable TV, WI-FI, Wireless Internet, Business Band, CB or Amateur Radio Antenna Installation.

Products   Recently Viewed