Call: (407) 944-8856

EZ NP-60-125 Non-Penetrating Roof Mount Low Profile for Light Antennas

3 Star Inc. EZ NP-60-125 Non-Penetrating Roof Mount - With 60" - 1.25" Mast
Made in the USA!
Ideal for Light Off-Air TV and Wireless Internet Antenna mounting, is constructed of pre-galvanized steel, uses 6 standard concrete blocks to anchor, 29 x 35.5" base, with 1.25" mast 60" in length . ( A 60" x 1.25" Swaged Pipe can be Added On )

For light antenna loads needing 10 feet in height, use this mount in combination with (2)EZ 5-16S swaged 1.25" O.D. masts, several EZ 50 turnbuckles, some 620 guy wire and the EZ 43-A Guy Ring! (available separately)

Also can be used as a non-pen base for an H20 or H30 Telescopic mast, though down guys will still be required as per Factory recommendations.

Specification Sheet

manufacturer

Easy Up

Protective Rubber Mat Layer for Non-Penetrating Antenna Roof Mount - $26.00

FRM-MAT Satellite Dish Non-penetrating Roof Mount Rubber Protective Mat
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 3/32 thick Pad measures roughly 36 wide by 42 inches long, trims neatly, place underneath Frame of Non-Penetrating mount, on top of Roof surface...

Protective Barrier Pad for Non-Pen Roof Mount - $48.95

3S-PAD Protective Barrier Pad for Roof Mount
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 3/8 thick Pad is for placement underneath the Frame of Non-Penetrating mount, on top of Roof surface...

3/8" Protective Barrier Pad for FRM Roof Mount 3S-FRMPAD - $96.00

3 Star FRMPAD Protective Barrier Pad for FRM Mounts
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 3/8 thick Pad measures roughly 18 wide by 42 inches long, includes 2 each per set, place underneath Frame of Non-Penetrating mount, on top of Roof surface...

Non-Penetrating Mount Guy Wire Kit - $24.95

Guy Wire Kit for Non Pen Mounts up to 2-1/4"

Made in the USA!
Complete kit for guying down a mast up to 2.25" diameter. Includes guy wire, guy ring, S hooks, turnbuckles and cable clamps. Mast not included. Read More

5' Foot by 1.25" OD 18 AWG Galvanized Antenna Mast Pole - Swaged | EZ 5-18S - $14.95

EZ 5-18S 5 Foot 18 AWG Swaged Antenna Mast Section
Made in the USA!
This 5 Foot (60") by 1.25" OD 18 AWG swaged end Antenna Mast tube is galvanized for weather and used to extend any 1-1/4 inch 18 gauge antenna masts by fitting the swaged end of this mast into the open end of the other mast tube, thereby extending the existing mast an additional 5 feet. Manufacturers recommend that masts heights of 10 feet and higher be guyed...

Rate this product.

Product isn't rated yet. Write a review.

Flat Roof Non-Penetrating Mounts

These mounts can be used where penetrating its attachment is not an option. Non penetrating mounts use a balasest like your usual cement cinder block as a method to hold down your masting structure. They can help meet the variety of communication tower needs such as Cellular, PCS, Wireless Cable, Microwave, Wireless Internet, WiFi Hot Spots, DBS, MDS, MMDS and UHF/VHF reception.

Designed and engineered to handle the job of getting above ground interference, each non-penetrating roof mount has been researched and developed to serve a specific purpose.

With professionally engineered construction, you can be assured you're getting a virtually maintenance-free product built to the highest standards. And because our non-penetrating roof mounts are hot-dip galvanized after fabrication, our mounts won't rust.

Additional Features Include