Your Cart
Credit Cards Taken
Your shopping cart is empty!
We Ship Fast!
Your Orders leave Daily! UPS... What can Brown do for You?!United States Postal ServiceR+L Carriers... Value Added Advantages!
Printer Friendly Tell a Friend

Telescopic Antenna Mast Heavy Duty Base Plate with Collar EZ32C

Highlights
Galvanized Steel
Base Plate for:
ROHN H20, H30, H40, H50 and Channel Master 1620, 1630, 1640, 1650, 1820, 1830, 1840, 1850
Collar is 2.25 Inch ID
6 inch tall collar
Price: $18.95
Manufacturer Code: EZ 32C
Stock Level: 5
Qty:
Availability: Usually ships in 24 Hrs
Shipping: Can ship anywhere
Easy Up EZ 32C Heavy Duty Base Plate with Collar for Telescopic Mast Pole
Made in the USA!Made in the USA!
Is designed to support and ground ROHN H20, H30, H40, H50 and Channel Master 1620, 1630, 1640, 1650, 1820, 1830, 1840, 1850 Telescopic (Push-Up) Antenna Masts. Bottom segment of Mast up to 2.25 inch Inserts into 6 inch tall Collar with set screw with outer plate dimensions of 9 x 9 inches. Bonding can be made by affixment to Mast. Consult NEC and Applicable Local Code for further guidance. As with all Masts, Guy wire support and Grounding are Critical to Antenna Survival.


Note: This Base Plate is THE Base Plate to use with ROHN H30, H40, H50 and Channel Master 1620, 1630, 1640, 1650, 1820, 1830, 1840, 1850 Telescopic (Push Up) Masts. All the other plates have a Rod or angle piece that the Tube of the Mast centers around loosely. This Plate has a collar with a Set Screw that securely holds the Telescopic Mast Tube in place and can be in turn, cemented into the concrete Pad via the Pin provided. The word "Ground" as used in the description can be a bit of a misnomer; it does not provide a "Earth Ground" in and of itself, but rather is a junction component that rests on the ground or pad and should be Bonded to with a proper Earth Ground composed of a 5/8 inch by 8 foot Copper Clad Ground Rod as a minimum. Consult your Local Building Code and NEC for guidance to Properly Grounding your HD TV, WI-FI, Wireless Internet, Business Band, CB or Amateur Radio Antenna Installation.
Product isn't rated yet. Write a review.

Telescopic Mast Accessories

Remember those older AM/FM Portable Radios with the antenna that you extended by pulling it out? Or the Radio Antennas on older cars that would pop-out, extend and retract when you turned on the radio? This Mast isn't an Antenna, but it extends and retracts by hand in similar fashion. Available in 20', 30', 40' and 50' heights. All ROHN telescoping masts are pre-galvanized and come assembled with hardware. Erection is made by simply connecting guys and brackets to the attached unique heavy duty rolled edge guy rings and clamps, extend each section one at a time (starting with the innermost section), insert the locking cotter pins, rotating the tubes to a locked position, and tightening the clamps. Repeat the process on each successive section until fully erect.

The unique ROHN Products design features interior tube flanging combined with a double crimped exterior tube to produce a stronger and more stable joint than most common masts. This design exclusive also prevents the sections from accidentally pulling apart and allows disassembly by pulling each section out through the lower end.
Each section extends deeper in to the lower tubes than most other designs, adding still further to the stability of the structure.

H Series
This heavy duty series uses 1-1/4" 16 gauge galvanized tubing for top section. All other sections are 18 gauge.

Assembly
1. Secure base and anchors (sold separately).
2. Attach lowered mast to base.
3. Secure guy lines to the lower Guy Ring and attach to anchors. Align the mast vertically by tightening the Guy Lines.
4. Secure upper Guy Ring using the appropriate Mast Clamp to desired location on the upper Tube (see note 8 on page 10).
5. Secure appropriate length guy lines to the upper Guy Ring and let them hang.
6. Raise the upper Tube and inset the cotter pin. Make sure that the cotter pin is inside the notch in the inside tube.
7. Secure the cotter pin and tighten the mast clamp.
8. Secure appropriate length guy lines to the next highest Guy Ring, and let them hang.
9. Raise the next smallest Tube and insert the cotter pin. Make sure that the cotter pin is inside the notch in the inside tube.
10. Secure the cotter pin and tighten the mast clamp.
11. Repeat steps 8-10 until all sections have been raised and are secured.
12. Attach all hanging Guy Lines to their respective anchor. Align the mast vertically by tightening the Guy Lines. Make sure to work your way up the mast while tightening.


ROHN Telescoping Masts



ROHN H-Series Masts


Get Adobe Reader



This Buyers Guide has will answer many questions you may have on this Product Line. For more detailed information and Specification Sheets covering many aspects of Various Parts, Accessories and Installation Scenarios... Please refer to the "Telescopic Mast" Link appearing in the Footer of this Page Below!

Telescoping Masts are not recommended for commercial, CB or beam antenna installations.

Products   Recently Viewed