Call: (407) 944-8856

618 Telescopic Antenna Mast Down Guy Wire 1000 Feet

618 Telescopic Antenna Mast Down Guy Wire

Made in the USA!
Twenty 50 foot Loops of Heavy Duty Pre-Galvanized 6 Strand, 18 Gauge Guy Wire totaling 1000 continuous feet. Perfect for Guying Down All Telescopic and Heavy Duty Antenna Mast Load Applications. Comes as Contiguous Footage totaling 1000 feet with 700 lbs Breaking Strength ...

Note:

When Selecting Guy Wire for use in Guying Antenna Masts, Consider the Height, Antenna Size and Wind Loading being presented. This Stranded (6 Strands of 18 Gauge wire) Guy Wire is Just fine for All Telescopic Antenna Mast Guying Scenarios of Any Height and Wind Load Applications. Make Sure that the Anchor Points are just as Heavy Duty as this Stranded Guy Wire!

1/8" Down Guy Wire Cable Clamp Galvanized Forged Steel 1/8CCF - $0.95

ROHN 1/8CCF 1/8" Down Guy Wire Cable Clamp Galvanized Drop Forged Steel
Use 2 of these when Terminating 620 (CM 9080) and 618 (ROHN 618) wire strand used in Telescopic and Regular TV Antenna Mast Down Guys for both Temporary and Permanent Scenarios...

1/4 inch Heavy Duty Open Eye Wire Rope Thimble 1/4THH - $1.15

ROHN 1/4THH 1/4 inch Heavy Duty Open Eye Wire Rope Thimble
For use in forming Down Guy Dead-ends with 3/16" Bare Strand and cable clamps or 618, 620 Telescopic Antenna Mast Down Guy Wire Rope using several 1/8 inch Cable Clamps...
Read More

Gripple 1/8" Cable Rope Grip for 620 Telescopic Antenna Mast Down Guy Wire - $6.25

Gripple 1/8" 20ga Down Guy Wire Cable Rope Grip
Use with Gripple Tool (TGTP) when Terminating 6-20 (CM 9080) guy wire strand. Used in Telescopic and Regular TV Antenna Mast Down Guys to easily Secure and Tension Multiple Guy Wires at the Anchor end...

3/8TBE&J Turnbuckle for ROHN Tower 3/8 x 6 inch Eye to Jaw - $10.95

ROHN 3/8TBE&J 3/8" x 6" Eye to Jaw Turnbuckle
Federal Spec FF-T-791B Type 1 Form 1; Forged, Hot Dip Glavanized, Open Body, Working Load Limit: 1200 lbs., Ultimate Strength: 6000 lbs.
Typical Use: when attaching and tensioning ROHN Tower and Telescopic Antenna Mast Down Guy terminations 3/16" Strand via Pre-formed deadend and 5/16THH, 1/4" Bare Strand via Cable Clamps and 5/16THH, or 618/620 Bare Wire via Cable Clamps/Gripple and 1/4TH) to Closed Eye or Integral Equalizer Plate Anchors (like GAS4303/EZ 30 or GAC3455). Will NOT fit a GAR30 Anchor... Read More

Rate this product.

Product isn't rated yet. Write a review.

Masting Accessories

Masting Accessories that include Down Guy Rings, Anchors, Wire, Screws, Clamps, Pitch Pads or Rubber Mats, Wire Thimbles, etc! Though most Mounts come with the minimal amount of Requisite Hardware, it by no means accounts for all Mounting Options, Materials and Custom Installation Scenarios.

Take a moment to Consider the Options and Materials in Use. Then Select the Appropriate Hardware to realize your Goal. The Flexibility and Longevity of any Mount to Match the Mounting Conditions may depend on it.